How to photograph or scan your artwork so it prints well
A print can only be as good as the file it is made from, so digitising your artwork is the step that decides everything after it. The short answer: scan the piece if you can, because a scan holds tone and fine detail more accurately than a photograph. Photograph it when scanning is not practical. Then run the four checks at the end of this guide before you sell a single print from the file.

First, what we need from you
We print from a digital file. We do not scan, photograph or digitise originals in-house, so please do not send us the artwork itself. What you upload is a JPEG, a TIFF or a PNG, and everything below is about making that file a faithful copy of the piece.
Scanning
For small, flat work on paper, a flatbed scanner at home can do the job. Clean the glass, lay the work flat, and switch off any automatic enhancement or sharpening in the scanner software, because you want the artwork as it is. Scan big. A setting of 1200 DPI is ideal, where DPI simply means how many dots the scanner records for each inch of your artwork. A large scan can always be made smaller later. A small one cannot be made larger.
For anything large, delicate or important, use a professional scanning service. We recommend Cultural Heritage Digitisation (CHD) in Wandsworth, London, who scan original artworks on a large-format scanner that does not touch the surface of the work. We have no commercial arrangement with them or with anyone else, so use whoever suits you. Scan quality varies a lot between providers, so check reviews before you book, and ask for a flattened, high-resolution TIFF. Allow time for it as well: a scanning booking is separate from your print order and adds to your schedule.
Photographing with a phone and a window
A phone camera in soft daylight can work. The method comes down to even light, a square-on camera and a steady hand.
Light. Work beside a large window, out of direct sun. A bright, overcast day is ideal. You want flat light with no shadows and no bright patches. Switch off the lamps and ceiling lights in the room: mixing daylight with bulbs gives the picture two different colours of light, and that is hard to correct afterwards.
Position. Hang the piece on a wall or prop it upright, and hold the camera exactly parallel to it, centred on the middle of the work. If the camera tilts, a rectangle turns into a trapezium. Use the main lens, not the wide-angle one, then fill as much of the frame with the artwork as you can, so that you keep as many pixels as possible.
Steadiness. Use a tripod if you have one, or brace the phone against something solid. Take several shots and keep the sharpest.
Glass and shine. Take the work out of its frame if you can, because glass reflects everything. For varnished or glossy work, change the angle of the light until the bright patches disappear.
A colour reference. Put a photographer's grey card beside the work in one of the shots. It gives you, or anyone who edits the file, a known neutral to correct the colour against.
If you have a camera
The same rules apply, with more control. The best set-up is two matched lights, one on each side at roughly 45 degrees and the same distance from the work, with the camera on a tripod. Shoot RAW, keep the ISO low, set the aperture to around f/8 and set the white balance manually. If those words mean nothing to you, that is fine. The phone method will get you started, and a professional scan is there for the work that matters most.
Four checks before you sell from the file
1. Is it big enough? Look up the pixel dimensions of the file. Divide each by 200 and you have, in inches, roughly the largest print it will make well. Divide by 300 for the size at which it will look its very best. A file of 4,000 by 5,000 pixels is at its best up to about 13 by 17 inches and can stretch to 20 by 25. As a guide, keep files from a 12 megapixel phone to the smaller sizes. Anything under 2 megapixels is refused at upload.
2. Is it sharp? Zoom in to 100% on the parts that matter: an edge, a line, a brush mark. If it is soft on screen, it will be soft on paper. Software can enlarge a file, but that adds pixels, not detail.
3. Is the colour right? Put the original next to your screen in daylight and compare the two. Look hardest at the whites. Paper that should be white often photographs grey or cream, and that tint is in the file, so it will be in the print. Correct it before you upload. Our colour guide covers the screen side of this.
4. Does it survive on paper? Order a test strip: a 4 by 30 inch strip of your image on the paper you plan to use. It shows colour, contrast and sharpness in a way no screen can, and it is the cheapest way to find a problem before your buyers do.
Saving and uploading
Work from the original file, not a copy that has been through email or a messaging app, because those are usually shrunk on the way. Save it as a JPEG at maximum quality or as a flattened TIFF. If you photographed with an iPhone, export a JPEG first: HEIC files are refused at upload. Keep the colour profile embedded when you save. If your software offers a choice of profile, Adobe RGB (1998) is the one we recommend.
The step-by-step versions are in the help centre: How should I photograph my artwork before uploading it?, How to prepare files for print and How to upload artwork.
Our view
Digitising is the least glamorous part of selling prints and the part most worth doing properly. You do it once for each piece, and every print you ever sell of that work is made from it. Give it the afternoon. After that, the rest of the journey is a handful of decisions.
Liked this? Get the rest by email
The drop playbook: five short emails from the same team.